Motorola CPCI-6115 Servisní příručka Strana 114
- Strana / 196
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Control via IPMI
CPCI-6200 Installation and Use (6806800J66C)
114
6.3.1.2 Continue Firmware Upgrade
The Continue Firmware Upgrade command writes a part of the firmware image to the target
IPMC. It also checks file integrity and makes the target IPMC leave the firmware upgrade mode
if an error occurs. If an error occurs, the whole firmware upgrade sequence must be repeated
beginning from the Start Firmware Upgrade command and the whole firmware upgrade
image must be retransmitted.
6.3.1.2.1 Request Data
The following table lists the request data applicable to the Continue Firmware Upgrade
command.
6.3.1.2.2 Response Data
The following table lists the response data of the Continue Firmware Upgrade command.
6.3.1.3 Finish Firmware Upgrade
The Finish Firmware Upgrade command makes the target IPMC leave the firmware upgrade
mode.
Table 6-12 Request Data of Continue Firmware Upgrade
Byte Data Field
1..23 Firmware content to be sent to the target IPMC.
The firmware image is a Motorola SREC file.
The whole message length is defined by the maximum IPMB message length.
Table 6-13 Response Data of Continue Firmware Upgrade
Byte Data Field
1Completion Code
0x00: Command executed successfully
0x1..0xFF: Error, that means the IPMC left the firmware upgrade mode
- CPCI-6200 1
- Trademarks 2
- Contact Address 2
- Contents 3
- List of Tables 10
- List of Figures 13
- About this Manual 15
- Conventions 18
- Summary of Changes 19
- Introduction 21
- 1.2 Standard Compliances 24
- 1.3 Mechanical Data 26
- 1.4 Ordering Information 26
- 1.5 Product Identification 27
- Chapter 2 29
- 2.1 Overview 29
- 2.4 Power Requirements 31
- 2.5 Installing Accessories 32
- PMC Filler Plate 33
- PMC Alignment 33
- Voltage Key 33
- 2.6.3 Hardware Configuration 35
- 2.10 Factory-Installed Linux 42
- Chapter 3 45
- 3.1 Board Layout 45
- 3.2 Front Panel 46
- 3.3 Connectors and Headers 47
- 3.3.1 CPCI Bus Connector, J1 48
- 3.3.2 CPCI Bus Connector, J2 49
- 3.3.4 CPCI Connector, J4 51
- 3.3.7 Ethernet Connector 58
- 3.3.8 USB Connector 58
- 3.4 Switches 66
- 3.5 Front Panel LEDs 67
- 3.6 Status Indicators 68
- Functional Description 71
- 4.4 System Memory 74
- 4.5 Timers 75
- 4.6 Ethernet Interfaces 75
- 4.7 Local Bus Interface 75
- 4.7.3 Control and Timers PLD 77
- 4.8 DUART Interface 78
- 4.9 PCI Express Port 79
- 4.10 PCI/PCI-X Bus 80
- 4.11 Operation Modes 81
- 4.11.1 System Controller Mode 82
- 4.11.2 Peripheral Mode 82
- 4.11.3 Stand Alone Mode 83
- 4.12 PCI Express Expansion 84
- 4.13 System Interrupts 85
- 4.14 Clock Distribution 86
- 4.15 MPC8572 System Clock 87
- 4.16 Reset Control Logic 87
- 4.16.1 Abort/Reset Switch 89
- 4.16.2 Reset Timing 90
- 4.17 RTC Battery 91
- 4.18 IPMI Controller 91
- 4.19 Programmable Devices 93
- 4.19.1 Local Bus Control CPLD 94
- 4.19.2 Reset CPLD 94
- 4.19.3 CPCI Control CPLD 94
- 5.4 MOTLoad Commands 96
- 5.6 MOTLoad Tests 96
- 5.7 Using MOTLoad 97
- 5.7.2 Command Line Help 99
- 5.7.3 Command Line Rules 99
- 5.8 MOTLoad Command List 100
- MOTLoad Firmware 101
- Control via IPMI 107
- 6.1.3 IPMI Messaging Commands 108
- 6.1.4 SEL Device Commands 108
- 6.1.5 SDR Repository Commands 109
- 6.1.6 FRU Inventory Commands 109
- 6.1.7 Sensor Device Commands 110
- 6.2 PICMG 2.9 Commands 111
- 6.3 Emerson Specific Commands 112
- 6.3.2 OEM Commands 115
- 6.3.2.1 BMC/PM Change Role 116
- 6.4 FRU Information 118
- 6.5 Sensor Description 118
- Memory Maps and Addresses 137
- 7.2 CPCI-6200 Memory Map 138
- 7.4 System I/O Memory Map 140
- 7.4.1 System Status Register 143
- 7.4.2 System Control Register 144
- 7.4.5 Interrupt Register 1 148
- 7.4.6 Interrupt Register 2 149
- 7.4.7 Interrupt Mask Register 150
- 7.4.23 PLD Revision Register 167
- 7.4.24 PLD Date Code Register 168
- 7.4.25 Test Register 1 168
- 7.4.26 Test Register 2 169
- 7.4.27.2 Control Registers 170
- 7.4.27.3 Compare Registers 171
- 7.4.27.4 Counter Registers 172
- 7.5 Interrupt Controller 173
- C Device Addresses 174
- 7.7 PCI/PCI-X Configuration 175
- Replacing the Battery 179
- A.2 Replacing the Battery 180
- Related Documentation 181
- B.3 Related Specifications 183
- Safety Notes 185
- Installation 186
- Operation 187
- Hot Swap 188
- Sicherheitshinweise 189
- System Installation 191
- Batterie 192
- © 2009 Emerson Electric Co 196
Související produkty a manuály pro Síťové přepínače Motorola CPCI-6115
Síťové přepínače Motorola CPCI-6115 Servisní příručka
(174 stránky)
(174 stránky)
Síťové přepínače Motorola WS2000 - Wireless Switch - Network Management Device Specifikace
(346 stránky)
(346 stránky)
Síťové přepínače Motorola CPCI-6115 Servisní příručka
(138 stránky)
(138 stránky)
Síťové přepínače Motorola T1/E1 Uživatelský manuál
(25 stránky)
(25 stránky)
Síťové přepínače Motorola T1/E1 Specifikace
(122 stránky)
(122 stránky)
(31 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.683 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce