Motorola USB08 Provozní pokyny stáhnout pdf (Strana 56)

100

8.21 Reset RESET

Format

RESET

This command, which is only available when 'PC controls reset' is checked on the Settings>COM Port

tab, and the necessary hardware is in place, allows Xplor8 to reset the MCU remotely by toggling an

RS232 control pin. This is a convenience, but you can still use Xplor8 without this facility.

This command is only available when connected, i.e. when the COM port is open.

The 'Reset' speedbutton may be used as a quick way of issuing this command.

1 2 ... 51 52 53 54 55 56 57 58 59 60 61 ... 99 100

Xplor8 - Version 1 1
CONTENTS 3
1 INTRODUCTION 7
1.4 Xplor8 Source Code 8
1.5 Philosophy 8
1.6 Development History 8
1.7 Getting Started 9
1.8 Note on the Author 9
1.10 An Appeal 9
2 MISCELLANEOUS 10
2.5 Supporting Files 11
2.6 Remote Reset 11
2.9 USB-to-Serial Adapters 12
3 MON08 MONITOR FIRMWARE 13
3.4 Security Bytes 14
3.2 Utility Files 14
3.3 Entering Monitor Mode 14
3.5 Baud Rates 15
4 MEMORY MANAGEMENT 16
5 DEBUGGING 17
6 PROGRAM FEATURES 18
6.2 Main Menu 19
6.3 Speedbuttons 19
6.4 Output Window 19
6.5 Command History Window 20
6.6 Command Edit Box 20
6.7 Status Line 21
6.8 Information Sidebar 21
6.9 Add to Watch 23
6.10 File Menu 23
6.11 View Menu 24
6.12 Actions Menu 25
6.13 Macro Menu 26
6.14 Settings Menu 26
6.15 Help Menu 26
6.16 Keyboard Shortcuts 27
6.18 Base Converter 28
7 CONFIGURATION 31
7.3 Settings>COM Port 33
7.4 Settings>Macros 35
7.5 Settings>Debug 36
7.7 Settings>Notes 39
8 COMMANDS 40
8.2 Path Tokens 41
8.4 Clear Local Memory CLM 43
8.5 Clear Output Window CLS 43
8.6 Connect / Disconnect 43
8.7 Edit Flash Byte EFB 44
EFB EE00 1D 44
8.8 Fill Memory F 45
8.9 Find Bytes FIND 46
8.10 Find Next NEXT 47
8.11 Go (Run) G 48
G * NextBreakAddr 48
8.12 List Macros LM 49
8.13 List Memory L 50
8.14 Load Memory LD 51
8.15 Mass Erase ME 52
8.16 Mode Switch MODE 52
8.17 Modify Memory M, MM 53
8.18 Page Erase PE 54
8.19 Pause PAUSE 54
8.21 Reset RESET 56
8.22 Save Memory SV 57
8.23 Send Bytes SEND 58
8.25 Trace T 60
8.26 Step Over O 61
8.27 Unassemble U 62
8.28 Using a Symbol Table 63
8.29 Unlock UNLOCK 65
8.30 Verify V 66
8.31 Verify Erase VE 67
9 AUTOMATION 68
9.3 Boot Script 69
9.4 Autostart Macro 70
9.5 Replaceable Parameters 70
9.7 Macro Editor 72
10 TERMINAL WINDOW 74
10.5 Terminal Window Settings 76
11 ERRORS 78
11.2 Diagnostics 79
11.3 Error Report 79
11.4 Command Line Errors 79
APPENDIX B - HARDWARE 81
QUICK TOUR 95
Revision History 100

Komentáře k této Příručce

Žádné komentáře

Motorola USB08 Provozní pokyny Strana 56

Komentáře k této Příručce

Související produkty a manuály pro Sítě Motorola USB08