Motorola MS3204 Specifikace Strana 104
- Strana / 260
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
9 - 2 Symbol MiniScan MSXX04 Series Integration Guide
Troubleshooting
Table 9-1
Troubleshooting
Problem Possible Cause Possible Solutions
No red LED or nothing
happens during a scan
attempt.
No power to the scanner. Check the system power.
Confirm that the correct host interface cable is
used.
Connect the power supply.
Re-connect loose cables.
Scanner cannot read the bar
code.
Interface/power cables are
loose.
Re-connect loose cables.
Scanner is not programmed
for the correct bar code type.
Make sure the scanner is programmed to read the
type of bar code to be scanned.
Scan other bar code(s) and bar code types.
Incorrect communication
parameters.
Set the correct communication parameters (baud
rate, parity, stop bits, etc.)
Bar code symbol is
unreadable.
Check the symbol to make sure it is not defaced.
Try scanning similar symbols of the same code
type.
Inappropriately hot
environment.
Remove the scanner from the hot environment,
and allow it to cool down.
Laser activates, followed by a
beep sequence.
Beeper is configured. Refer to
Table 3-1 on page 3-7
for beeper
indication descriptions.
- Symbol MiniScan MSXX04 Series 1
- Integration Guide 3
- Warranty 4
- Revision History 5
- Table of Contents 7
- Table of Contents vii 9
- Table of Contents ix 11
- Table of Contents xi 13
- About This Guide 15
- Notational Conventions 16
- Related Documents 17
- Service Information 17
- Chapter 1 Getting Started 19
- Symbol MS954 Features 20
- Typical Applications 21
- Block Diagrams 21
- Symbol MS954 Block Diagram 22
- Getting Started 1 - 5 23
- Chapter 2 Installation 25
- Mounting 26
- Installation 2 - 3 27
- Assembling the Stand 28
- Mounting the Stand (optional) 29
- Connecting the MiniScan 31
- Location and Positioning 32
- Installation 2 - 9 33
- Scan Beam 35
- W=Symbol Width 35
- F=Field Width 35
- Window Material 36
- H=Symbol Height 36
- Installation 2 - 13 37
- Window Coatings 38
- Installation 2 - 15 39
- Accessories 40
- Installation 2 - 17 41
- Chapter 3 Scanning 43
- Smart Raster Scan Pattern 44
- Omnidirectional Scan Pattern 46
- Scanning Tips 47
- Trigger Options 47
- Level Trigger 48
- Pulse Trigger 48
- Host Trigger 48
- Beeper and LED Definitions 49
- Table 4-1 52
- Figure 4-2 53
- Figure 4-3 54
- Table 4-2 55
- Symbol MS1204FZY Decode Zone 57
- Table 5-1 60
- Figure 5-2 61
- Figure 5-3 62
- Table 5-2 63
- Figure 5-4 65
- Symbol MS2204 Decode Zones 66
- Table 5-3 67
- Symbol MS2204 2D Decode Zone 68
- Chapter 6 Symbol MS2204VHD 71
- Specifications 71
- Table 6-1 72
- Figure 6-2 73
- Figure 6-3 74
- Table 6-2 75
- + 15° from normal 77
- + 30° from normal 77
- + 4° from normal 77
- Symbol MS2204VHD Decode Zones 78
- Table 6-3 79
- Depth of Field 80
- Figure 7-1 84
- Table 7-1 84
- Figure 7-2 85
- Figure 7-3 86
- Table 7-2 87
- +4° from normal 89
- Table 7-3 91
- Figure 8-1 96
- Table 8-1 96
- Figure 8-2 97
- Figure 8-3 98
- Table 8-2 99
- + 50° from normal 100
- + 65° from normal 100
- 35° from normal 100
- Symbol MS954 Decode Zone 101
- Usable Scan Length 102
- Introduction 103
- Maintenance 103
- Troubleshooting 104
- Table 9-1 105
- Chapter 10 Parameter Menus 107
- Operational Parameters 108
- Default Table 108
- Parameter Menus 10 - 3 109
- Table 10-1 110
- Parameter Menus 10 - 5 111
- Parameter Menus 10 - 7 113
- Set Default Parameter 114
- Set Defaults - Symbol MS954 115
- Scanning Options 116
- Beeper Tone 117
- Parameter # 91h 117
- Beeper Frequency Adjustment 117
- Parameter # F0h 91H 117
- Laser On Time 118
- Parameter # 88h 118
- Scan Angle 118
- Parameter # BFh 118
- Power Mode 119
- Parameter # 80h 119
- Trigger Modes 120
- Parameter # 8Ah 120
- Scanning Mode 121
- Parameter # 8Dh 121
- Aiming Mode 122
- Parameter # F0h 7Eh 122
- Parameter # E4h, E5h 123
- Parameter # 89h 124
- Parameter # 90h 124
- Beep After Good Decode 125
- Parameter # 38h 125
- Transmit “No Read” Message 126
- Parameter # 5Eh 126
- Parameter Scanning 127
- Parameter # ECh 127
- Linear Security Level 1 128
- Linear Security Level 2 128
- Linear Security Level 3 129
- Linear Security Level 4 129
- Bi-directional Redundancy 130
- Parameter # 43h 130
- Enable/Disable UPC-A 131
- Parameter # 01h 131
- Enable/Disable UPC-E 131
- Parameter # 02h 131
- Enable/Disable UPC-E1 132
- Parameter # 0Ch 132
- Enable/Disable EAN-8 133
- Parameter # 04h 133
- Enable/Disable EAN-13 133
- Parameter # 03h 133
- Enable/Disable Bookland EAN 134
- Parameter # 53h 134
- UPC/EAN Coupon Code 135
- Parameter # 55h 135
- Decode UPC/EAN Supplementals 136
- Parameter # 10h 136
- Parameter Menus 10 - 31 137
- Parameter Menus 10 - 33 139
- Parameter # 50h 140
- Transmit UPC-A Check Digit 141
- Parameter # 28h 141
- Transmit UPC-E Check Digit 141
- Parameter # 29h 141
- Transmit UPC-E1 Check Digit 142
- Parameter # 2Ah 142
- UPC-A Preamble 143
- Parameter # 22h 143
- UPC-E Preamble 144
- Parameter # 23h 144
- UPC-E1 Preamble 145
- Parameter # 24h 145
- Convert UPC-E to UPC-A 146
- Parameter # 25h 146
- Convert UPC-E1 to UPC-A 147
- Parameter # 26h 147
- EAN Zero Extend 147
- Parameter # 27h 147
- Bookland ISBN Format 148
- Parameter # F1h 40h 148
- UPC/EAN Security Level 0 149
- UPC/EAN Security Level 1 149
- UPC/EAN Security Level 2 149
- UPC/EAN Security Level 3 149
- UPC Half Block Stitching 150
- Parameter # 4Ah 150
- Linear UPC/EAN Decode 150
- Parameter # 44h 150
- Code 128 151
- Enable/Disable ISBT 128 152
- Parameter # 54h 152
- Lengths for Code 128 152
- Code 128 Decode Performance 153
- Parameter # 48h 153
- Parameter # 49h 154
- Enable/Disable Code 39 155
- Parameter # 00h 155
- Parameter # 0Dh 155
- Convert Code 39 to Code 32 156
- Parameter # 56h 156
- Code 32 Prefix 157
- Parameter # E7h 157
- Set Lengths for Code 39 158
- Parameter # 30h 159
- Transmit Code 39 Check Digit 159
- Parameter # 2Bh 159
- Parameter # 11h 160
- Code 39 Decode Performance 161
- Parameter # 46h 161
- Parameter # 47h 162
- Enable/Disable Code 93 163
- Parameter # 09h 163
- Set Lengths for Code 93 164
- Code 11 165
- Set Lengths for Code 11 166
- Parameter # 34h 167
- Transmit Code 11 Check Digit 168
- Parameter # 2Fh 168
- Interleaved 2 of 5 169
- Parameter # 31h 171
- Transmit I 2 of 5 Check Digit 172
- Parameter # 2Ch 172
- Convert I 2 of 5 to EAN-13 172
- Parameter # 52h 172
- Discrete 2 of 5 173
- Chinese 2 of 5 175
- Enable/Disable Codabar 176
- Parameter # 07h 176
- Set Lengths for Codabar 177
- CLSI Editing 178
- Parameter # 36h 178
- NOTIS Editing 178
- Parameter # 37h 178
- MSI Plessey 179
- Set Lengths for MSI Plessey 180
- MSI Plessey Check Digits 181
- Parameter # 32h 181
- Parameter # 2Eh 181
- Parameter # 33h 182
- PDF417/MicroPDF417 183
- MicroPDF Performance 184
- Parameter # F0h 65h 184
- Code 128 Emulation 185
- Parameter # 7Bh 185
- GS1 DataBar 186
- GS1 DataBar Expanded 187
- Parameter # F0h 54h 187
- Parameter # F0h 8Dh 188
- Composite 189
- Composite CC-A/B 190
- Parameter # F0h 56h 190
- Composite TLC-39 190
- Parameter # F0h 73h 190
- UPC Composite Mode 191
- Parameter # F0h 58h 191
- Data Options 192
- Parameter Menus 10 - 87 193
- Prefix/Suffix Values 194
- Parameter # EBh 195
- Baud Rate 197
- Parameter # 9Ch 197
- Baud Rate (continued) 198
- Parameter # 9Eh 199
- Check Parity 200
- Parameter # 97h 200
- Disable ACK/NAK Handshaking 201
- Enable ACK/NAK Handshaking 201
- Host RTS Line State 202
- Parameter # 9Ah 202
- Decode Data Packet Format 203
- Parameter # EEh 203
- Stop Bit Select 203
- Parameter # 9Dh 203
- Event Reporting 205
- Boot Up Event 206
- Parameter # F0h 02h 206
- Parameter Event 206
- Parameter # F0h 03h 206
- Macro PDF Features 207
- Transmit Unknown Codewords 208
- Parameter # BAh 208
- Escape Characters 209
- Parameter # E9h 209
- Delete Character Set ECIs 210
- Parameter # E6h 210
- ECI Decoder 211
- Parameter # E8h 211
- Transmit File Name 212
- Parameter # B0h 212
- Transmit Block Count 213
- Parameter # B1h 213
- Transmit Time Stamp 213
- Parameter # B2h 213
- Transmit Sender 214
- Parameter # B3h 214
- Transmit Addressee 214
- Parameter # B4h 214
- Transmit Checksum 215
- Parameter # B6h 215
- Transmit File Size 215
- Parameter # B5h 215
- Parameter # B7h 216
- Last Blocker Marker 216
- Parameter # B9h 216
- Numeric Bar Codes 217
- Numeric Bar Codes (continued) 218
- Parameter Menus10 - 113 219
- Revision String 221
- SSI Commands Not Supported 222
- Chapter 12 Mounting Templates 223
- Figure 12-2 224
- Figure 12-3 224
- RS-232 ASCII Character Set 225
- Table A-1 226
- ASCII Character Sets A - 3 227
- ASCII Character Sets A - 5 229
- USB ASCII Character Set 230
- ASCII Character Sets A - 7 231
- ASCII Character Sets A - 9 233
- ASCII Character Sets A - 11 235
- ASCII Character Sets A - 13 237
- ASCII Character Sets A - 15 239
- Glossary 241
- Glossary - 3 243
- Glossary - 5 245
- Glossary - 7 247
- Glossary - 9 249
- Glossary - 11 251
- Index - 3 255
- Tell Us What You Think 257
Související produkty a manuály pro Čtečky čárových kódů Motorola MS3204
Čtečky čárových kódů Motorola MS1207FZY Specifikace
(368 stránky)
(368 stránky)
(20 stránky)
Čtečky čárových kódů Motorola Phaser P460 Specifikace
(198 stránky)
(198 stránky)
Čtečky čárových kódů Motorola LS1203 Specifikace
(202 stránky)
(202 stránky)
Čtečky čárových kódů Motorola LI2208 Specifikace
(416 stránky)
(416 stránky)
Čtečky čárových kódů Motorola DS3508 Specifikace
(386 stránky)
(386 stránky)
Čtečky čárových kódů Motorola DS3508 Specifikace
(316 stránky)
(316 stránky)
Čtečky čárových kódů Motorola MC17U Specifikace
(24 stránky)
(24 stránky)
(2 stránky)
(36 stránky)DECOLAV 5255 manuels
Manuels d'utilisation et guides de l'utilisateur pour Meubles DECOLAV 5255.
Nous fournissons des manuels en pdf 1 DECOLAV 5255 à télécharger gratuitement par type de document : Manuel de l'utilisateur
Komentáře k této Příručce